YAMAHA MOTOR CORPORATION, U.S.A. STREET & ENDURO MOTORCYCLE LIMITED WARRANTY

0

Filed Under (Yamaha) by admin on 27-12-2011

download
GENERALEXCLUSIONS from this warranty shall include any failures caused by: a. Competition or racing use. b. Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts. c. Abnormal strain, neglect, or abuse. d. Lack of proper maintenance. e. Accident or collision damage. f. Modification to original parts. g. Damage due to improper transportation. SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance. THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to: 1. Operate and maintain the motorcycle as specified in the appropriate Owner’s Manual. 2. Give notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business. You may locate your nearest authorized Yamaha dealer through your local telephone directory. WARRANTY TRANSFER: To transfer any remaining warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha motorcycle dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer. Areasonable dealer imposed fee may be charged for the inspection. In no case will warranty be extended beyond the original period. EMISSIONS CONTROLSYSTEM WARRANTY Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha motorcycle covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the periods listed immediately below. Failures other than those resulting from defects in material or workmanship which arise solely as a result of owner abuse and/or lack of proper maintenance are not covered by this warranty.

Incoming search terms:

YAMAHA FZS6W OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Indicator and warning lights EAU11030 Turn signal indicator lights “ ” and “ ” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. NOTE: ● Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. ● This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a Yamaha dealer check the vehicle. EAU11423 Coolant temperature warning light “ ” This warning light comes on when the engine overheats. When this occurs, stop the engine immediately and allow the engine to cool. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir

YAMAHA FJR1300N PERIODIC MAINTENANCE AND MINOR REPAIR

0

Filed Under (Yamaha) by admin on 17-12-2010

download
Always keep the battery charged. Storing a discharged battery can cause permanent battery damage. ● To charge a sealed-type (MF) battery, a special (constant- voltage) battery charger is required. Using a conventional battery charger will damage the battery. If you do not have access to a sealed-type (MF) battery charger, have a Yamaha dealer charge your battery. EAU04076* Replacing the fuses The fuse box, which contains the fuses for the individual circuits, is located under panel D. The fuel injection system fuse box is located under panel D. The main fuse box is also located under panel D, beside the battery. (See page 6-7 for panel removal and installation procedures.) If a fuse is blown, replace it as follows. 1. Turn the key to “OFF” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage. 1. Fuel injection system fuse 2. Spare fuel injection system fuse 1. Headlight fuse 2. Signaling system fuse 3. Ignition fuse 4. Windshield motor fuse 5. Radiator fan fuse 6. Backup fuse (odometer and clock) 7. Spare fuse (〈 4)
PERIODIC MAINTENANCE AND MINOR REPAIR 6-31 6 EC000103 CAUTION: Do not use a fuse of a higher amperage rating than recommended to avoid causing extensive damage to the electrical system and possibly a fire. 3. Turn the key to “ON” and turn on the electrical circuit in question to check if the device operates. 4. If the fuse immediately blows again, have a Yamaha dealer check the electrical system. EAU04099 Replacing a headlight bulb This motorcycle is equipped with quartz bulb headlights. If a headlight bulb burns out, replace it as follows. 1. Remove panel B (if replacing the left headlight bulb) or panel C (if replacing the right headlight bulb). (See page 6-7 for panel removal and installation procedures.) 2. Disconnect the headlight coupler, and then remove the headlight bulb cove

Incoming search terms:

Yamaha VMX12/ VMX12C Owner's Manual

0

Filed Under (Yamaha) by admin on 14-12-2010

download
Main switch EAUO0028 The main switch controls the ignition and lighting systems. The various main switch positions are described below. EAU00032 ON All electrical systems are supplied with power, the headlight, meter lighting, taillight and front position lights come on, and the engine can be started. The key cannot be removed. EAU00038 OFF All electrical systems are off. The key can be removed. 1. Push. 2. Release. 3. Turn P (Parking) The meter light, taillight and position lights are on, but all other electrical sys- tems are off. The key can be removed. The key must be pushed in from the “OFF” position to be turned to “P”. ECA00043 Do not use the parking position for an extended length of time, otherwise the battery may discharge. 1. Neutral indicator light ‘NEUTRAL’ 2. Turn signal indicator light ‘TURN’ 3. Fuel level warning light ‘FUEL’ 4. High beam indicator light ‘HIGH BEAM’ 5. Oil level warning light ‘OIL LEVEL’ EAU03034 Indicator and warning lights EAU00062 Neutral indicator light “NEUTRAL” This indicator light comes on when the transmission is in the neutral position. EAU00059 Turn signal indicator light “TURN” This indicator light flashes when the turn signal switch is pushed to the left or right. his warning light comes on when the fuel level drops below approximately 3 L (0.7 Imp gal, 0.8 US gal). When this occurs, refuel as soon as possible. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Turn the key to “ON”. 2. If the warning light does not come on, have a Yamaha dealer check the electrical circuit. Oil level warning light “OIL LEVEL” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked according to the following procedure. 1. Turn the key to “ON”. 2. If the warning light does not come on, have a Yamaha dealer check the electrical circuit. NOTE: EAU00064 High beam indicator light “HIGH BEAM” This indicator light comes on when the high beam of the headlight is switched on. Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a mal- function

Incoming search terms:

YAMAHA YZF-R1R/ YZF-R1RC OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 03-12-2010

download
1. Right turn signal indicator light “” 2. Fuel level warning light “” 3. Oil level warning light “” 4. Neutral indicator light “” 5. Engine trouble warning light “” 6. High beam indicator light “” 7. Left turn signal indicator light “”
INSTRUMENT AND CONTROL FUNCTIONS 3-3 3 EAU04895 Oil level warning light “” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5seconds. If this occurs, have a Yamaha dealer check the motor- cycle. EAU00061 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position. EAU04896 Engine trouble warning light “” This warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this occurs, have a Yamaha dealer check the self-diagnosis system. (See page 3-7 for an explanation of the self-diagnosis device.) The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. EAU00063 High beam indicator light “” This indicator light comes on when the high beam of the headlight is switched on

Incoming search terms:

YAMAHAMOTOR CORPORATION, U.S.A. STREET AND ENDURO MOTORCYCLE LIMITED WARRANTY

0

Filed Under (Yamaha) by admin on 26-11-2010

download
any failures caused by: a. Competition or racing use. b. Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts. c. Abnormal strain, neglect, or abuse. d. Lack of proper maintenance. e. Accident or collision damage. f. Modification to original parts. g. Damage due to improper transportation. SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance. THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to: 1. Operate and maintain the motorcycle as specified in the appropriate Owner’s Manual. 2. Give notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business. You may locate your nearest authorized Yamaha dealer through your local telephone directory. WARRANTY TRANSFER: To transfer any remaining warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and

YAMAHA V-MAX PERIODIC MAINTENANCE AND MINOR REPAIR

0

Filed Under (Yamaha) by admin on 25-11-2010

download
PERIODIC MAINTENANCE AND MINOR REPAIR -. 1. Screw (x 2) EAU03003 Replacing the headlight bulb This motorcycle is equipped with a quartz bulb headlight. If the headlight bulb burns out, replace it as follows. 1. Remove the headlight unit by re- moving the screws. 2. Disconnect the headlight coupler, and then remove the headlight unit and bulb cover. 1. Headlight bulb holder 3. Remove the headlight bulb holder by turning it counterclockwise, and then remove the defective bulb. EWOOOl19 Headlight bulbs get very hot. Therefore, keep flammable products away from a lit headlight bulb, and do not touch the bulb until it has cooled down. 4. Place a new bulb into position, and then secure it with the bulb holder. 1. Do not touch this area. EC000105 Do not touch the glass part of the headlight bulb to keep it free from oil, otherwise the transparency of the glass, the luminosity of the bulb, and the bulb life will be adversely affected. Thoroughly clean off any dirt and fingerprints on the headlight bulb using a cloth moistened with alcohol or thinner. 5. Install the bulb cover, and then connect the coupler. 6. Install the headlight unit by install- ing the screws. 7. Have a Yamaha dealer adjust the headlight beam if necessary. 6-40 PERIODIC MAINTENANCE AND MINOR REPAIR 1. Screw (x 2) 1. Tail/brake light bulb (x 2) EAU00855 Replacing a turn signal light bulb or the tail/brake light bulb 3. Insert a new bulb into the socket, push it in, and then turn it clock- wise until it stops. 1. Remove the lens by removing the screws. 2. Remove the defective bulb by pushing it in and turning it counter- clockwise. 1. Turn signal light bulb 4. Install the lens by installing the screws. EC000108 Do not overtighten the screws, oth- erwise the lens may break

Incoming search terms:

YAMAH FJR PERIODIC MAINTENANCE AND MINOR REPAIR MANUAL

0

Filed Under (Yamaha) by admin on 22-11-2010

download
Battery The battery is located under panel D. (See page 6-7 for panel removal and installation procedures.) This motorcycle is equipped with a sealed-type (MF) battery, which does not require any maintenance. There is no need to check the electrolyte or to add distilled water. To charge the battery Have a Yamaha dealer charge the battery as soon as possible if it seems to have discharged. Keep in mind that the battery tends to discharge more quickly if the motorcycle is equipped with optional electrical accessories. EW000116 WARNING ● Electrolyte is poisonous and dangerous since it contains sulfuric acid, which causes severe burns. Avoid any contact with skin, eyes or clothing and always shield your eyes when working near batteries. In case of contact, administer the following FIRST AID. •EXTERNAL: Flush with plenty of water. •INTERNAL: Drink large quantities of water or milk and immediately call a physician. •EYES: Flush with water for 15minutes and seek prompt medical attention. ● Batteries produce explosive hydrogen gas. Therefore, keep sparks, flames, cigarettes, etc., away from the battery and provide sufficient ventilation when charging it in an enclosed space. ● KEEP THIS AND ALL BATTERIES OUT OF THE REACH OF CHILDREN. To store the battery 1. If the motorcycle will not be used for more than one month, remove the battery, fully charge it, and then place it in a cool, dry place. 2. If the battery will be stored for more than two months, check it at least once a month and fully charge it if necessary. 3. Fully charge the battery before in- stallation Replacing the fuses The fuse box, which contains the fuses for the individual circuits, is located under panel D. The fuel injection system fuse box is located under panel D. The main fuse box is also located under panel D, beside the battery. (See page 6-7 for panel removal and installation procedures.) If a fuse is blown, replace it as follows. 1. Turn the key to “OFF” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage.

Yamaha YZF-R6 SPECIFICATION AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 19-11-2010

download
Shift timing indicator light This indicator light can be set to come on and go off at the desired engine speeds and is used to inform the rider when it is time to shift to the next higher gear. The electrical circuit of the indicator light can be checked by turning the key to “ON”. If the indicator light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. (See pages 3-7-3-10 for a detailed explanation of the function of this indicator light and on how to set it.) EAU04923* Coolant temperature warning light “” This warning light comes on when the engine overheats. When this occurs, stop the engine immediately and allow the engine to cool. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. Multi-function display The multi-function display is equipped with the following: a speedometer (which shows the riding speed) an odometer (which shows the total distance traveled) two tripmeters (which show the distance traveled since they were last set to zero) a fuel reserve tripmeter (which shows the distance traveled since the fuel level warning light came on) a clock a self-diagnosis device a display brightness and shift timing indicator light control mode NOTE: Be sure to turn the key to “ON” before using the “SELECT” and “RESET” buttons. To switch the speedometer and odometer/tripmeter displays between kilometers and miles, press the “SELECT” button and “RESET” button together for at least two seconds. Odometer and tripmeter modes Pushing the “SELECT” button switches the display between the odometer mode “ODO” and the tripmeter modes “TRIP 1″ and “TRIP 2″ in the following order: ODO → TRIP 1 → TRIP 2 → ODO If the fuel level warning light comes on (see page 3-2), the odometer display will automatically change to the fuel reserve tripmeter mode “F-TRIP” and start counting the distance traveled from that point. In that case, pushing the “SELECT” button switches the display between the various tripmeter and odometer modes in the following order: F-TRIP → TRIP 1 → TRIP 2 → ODO → F-TRIP

Incoming search terms: