Harley-Davidson HEAT DEMONS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 27-03-2012

download
1. Remove the Right Handlebar Control, upper and lower switch housing screws, and Right Grip from the Handlebar according to the service-manual instructions and set aside or leave hanging. Remember to insert a spacer between the rear brake light switch and the lever to keep the switch from being broken. 2. Remove the Left Hand switch housing from the handlebar according to the service-manual instructions. 3. Using a T27 TORX drive head remove the half of the clamp that secures the clutch hand lever to the handlebar and discard. The Heat Demon controller will replace this clamp when finishing the installation. Separate the clutch hand lever assembly from the handlebar and move away from the bar. 4. Mark the location of the Left Grip and remove it by twisting, heating or with air pressure. Almost all grips can be removed without damage. If this does not work it may be necessary to cut the grip for removal. 5. A hole needs to be drilled in the bottom of the handlebar to route the power wires and wires from the Controller. The location of the hole should be in the groove or recess on the bottom of the handlebar under the Left Switch Housing at the end of the groove toward the grip. Start by punching a hole location with a center punch to pierce the chrome. Use safety glasses that completely cover the eyes to protect from steel chips while drilling! Start with a small drill like a 3/32″ size to make the initial hole. Then use progressively larger drills or a step drill to increase the hole size to 5/16″. After the hole is drilled use a round file or deburring tool to remove the sharp edges. 6. Uncoil the plastic snake from the kit and run it from the right end of the handlebar out the left end. Twisting the snake or inserting it vertically versus flat can help to push around the corners. 7. Attach the white and yellow wires from the Right Grip Heater (Item 3) to the hole in the plastic snake and pull them through the bar so they exit the left end. (See drawing below) 8. Push the right heater into the handlebar by squeezing it together and sliding it fully inside of the bar. The end of the heater with the orange cap should be pushed in first. Cut the white and yellow wire to extend 4 inches beyond the left end of handlebar. 9. Install the Right Throttle Control and Grip according to the service manua

KTM ELECTRICAL SYSTEMS INSTALLATION, REPAIR

0

Filed Under (KTM) by admin on 02-02-2012

download
DC SYSTEMS STEP DC1 – REGULATOR/RECTIFIER: PRE-2005 KTM If the stock regulator looks like below (the stock connector will not plug into the Trail Tech regulator/rectifier) then the provided stub connector must be soldered into the bike’s wire harness. For models without a stock battery, mount the reg/rec and plug the stub connector into it. Run the red and black wires directly to the (aftermarket) battery, and the yellow wires to the stator. SEE DC CIRCUIT DIAGRAM ON REVERSE SIDE OF PAGE. MODELS WITHOUT A STOCK BATTERY Move stock light to the DC circuit: divert lighting wire from AC circuit to DC circuit. In stock form, the lights are powered by the AC half of the electrical system. In order to continue to use the stock light, find the yellow wire (runs to stock headlight) shown below (wire bundles are found underneath gas tank) and cut the smaller gauge yellow wire. 1. Connect aftermarket light: Wire the light’s red(+) light lead to the positive(+) battery terminal, and the black(-) light lead to the negative(-) battery terminal. Trail Tech lights should use a 10-20 amp fuse as close to the positive(+) battery terminal as possible.

YAMAHA ROADSTAR TRIKE Removal of Clear Taillights and installation of Red Taillights

0

Filed Under (Yamaha) by admin on 16-02-2011

download
1 Installation of Lights 1.1 Support the trike on jack stands and remove the wheels. 1.2 Remove the clear lights from the inside of the wheel wells by unscrewing the three (3) screws from the light. 1.3 Unplug the wires and remove the lights. 1.4 Remove the chrome bezels and rubber gaskets from the clear lights and install on the red lights (5 screws). 1.5 Re-connect the wire plugs and install the red lights to the trike body using the same three screws. 1.6 Replace the wheels and torque the lug nuts to 75 lb.ft. 2 Wire modification inside trunk 2.1 From the inside of the trunk pull back the carpet on both the left and right hand sides to expose the wire harnesses coming from the wheel wells. 2.2 Locate the resistors in the harness, 2.5″ x 0.5″ x 0.5″, and covered by black shrink wrap. 2.3 Cut the shrink wrap to expose the resistors and cut wire on both side of the resistors. Remove and discard resistors. 2.4 Splice in the supplied 5″ green wires (WITHOUT the diodes) with 2 blue scotchlock connectors per side to reconnect the cut wires. 2.5 Do not glue in carpet until lights are tested. 3 Change to pigtail from Trike to Motorcycle. 3.1 Remove driver’s sear 3.2 Unplug pigtail from motorcycle (MC) wiring and trike body wiring. 3.3 Cut heat shrink on the MC plug side of the pigtail and pull expansion sleeve back to expose the wires. Figure 1 3.4 Cut Green and Yellow turn signal wires and about 3″ from the MC plug and splice in Green and Yellow wires from the supplied resistors with the supplied hest shrink solder connectors (heat to be applied) – (three wires in one connection) Figure 1 3.5 Cut the Red (Brake) and Brown (Running lights) wires and splice in the supplied diodes with the supplied heat shrink solder connectors. Red side of the diode wire facing the Trike plug. Figure 1 3.6 Connect eye lug on the black wire from the resistors to the negative terminal of the battery. Figure 2 3.7 Plug pigtail back into the Trike body and the MC

Incoming search terms:

Honda Shadow Aero 750 Turn Signal Cancellation Unit Installation Procedures

0

Filed Under (Honda) by admin on 29-11-2010

download
Left TurnSignal Right TurnSignal Turn Signal Switch (for ref. Only) CIRCUIT CONNECTIONS AFTER INSTALLATION of Cancellation Unit Original+12 volts motorcycle supply power for flasher Ground (thiswiredoesnot exist on all models) Output to switch Power Power Red Yellow Gray Green Ground Green/Red Blue/Red Turn Signal Cancellation Unit Identify the positive power wire to the turn signal flasher. A test light with the probe touched to this wire will stay on steady and flash with the turn signals. Cut the wire and install the connectors observing the polarity as shown. Connect the Red and Yellow wires as shown. not Identify the flasher output wire to the signal switch and attach the gray wire by soldering or use the supplied red tap connector. Place the unit in a suitable area on your particular motorcycle. It is suggested under the seat providing access to the turn signal flasher. Connect the units ground (green) wire to frame (neg) ground Assure it’sareliable connection. IF THE GROUND WIRE BECOMES DISCONNECTED THE UNIT WILL BURN UP. using the supplied ring terminal. Identify the brake light circuit per the motorcycle wiring diagram. Using a test light verify the correct circuit using the following procedure. Connect the test light alligator clip (negative side) to frame ground. Using the positive tip probe the circuit. The proper circuit will illuminate the the brake is applied. Attach the Green/Red wire to this circuit. test light when The factory cancellation time is set at approximately 23 flashes. The length of time for cancellation can be decreased to approximately 15 counts by setting the program listed in the programming box

Incoming search terms: