Kawasaki ZX6R 2009 Frame Slider Installation and removal Instructions

0

Filed Under (Kawasaki) by admin on 08-05-2012

download
1. Remove mid and lower body panels Left and Right. There is a small plastic cover that is mounted over the main engine stud location on the left side. This cover requires a small notch to be cut out of the cover to clear the small end of the left side offset. Remove stock stud and mount the left side offset (with 10 X 1.25 X 60). Using a pencil, trace out the notch that you need to remove to clear the small end of the offset. We used a Dremel tool with a sanding roll and cleaned it up with an exacto knife. We removed a small amount of material at a time checking for clearance each time. The notch will not be visible after the body has been mounted. See photos below: 2. Once you have notched the small left side panel, mount the left side offset but only hand tight. You need to be able to move the offset by hand to its proper location. 3. Mount the left side bodywork and align the offset to the opening in the body. Mount the left side slider on the offset to ensure correct location. There is a flat notch in the slider so the body will clear. Remove the slider and body and torque down the offset to OEM specifications. (see above)
4. Mount the left side panel. Install the slider using one drop of blue thread locker and torque down to 30 to 32 ft lbs.

2002 Kawasaki 360 ATV WINCH ACCESSORY INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 08-05-2012

download
1. Remove the two 8mm bolts that attach the front bumper assembly to the ATV frame see figure 3. 2. Place Winch mounting plate (A1) into position and fasten the two bent down tabs to the ATV frame using the two 8mm bolts removed in step one, see figure 4, and figure 5. Do not tighten fully at this time. 3. Attach the front of the mounting plate using four 1/4-20 u- bolts (B1), eight lock washers (B2), and eight 1/4-20 hex nuts (B3), see figure 6. 4. Tighten all fastners for the mounting kit at this time. 5. Place winch into position behind the mounting plate. Attach the top two feet of the winch using two 5/16-18 hex cap screws and lock washer. These fasteners will be found in the hardware kit that came with the winch. Note: The winch has floating nuts in its feet. In some instances, a nut may be moved off to one side making it impossible to screw a bolt in. If this becomes the case, take a screwdriver and center the floating nut in the winch to the bolt hole opening. Now attach the bolt through the Winch Plate and into the winch. 6. If using a Cast Hawse Fairlead: It may be neccasary to remove the cast hawse fairlead from the fairlead mounting plate that came with the winch.

2004 Kawasaki ZX10R Power Commander Installation Instructions

0

Filed Under (Kawasaki) by admin on 08-05-2012

download
Remove the main seat and the passenger seat 2. Remove the tail cover by removing the two bolts. 3 Place the Power Commander in the tail section and route the wiring harness on the inside of the tail section towards the front of the bike (Fig. A). 4. Remove the fuel tank. 5. Remove the air box lid by removing the 8 screws around the outer edge (Fig. B). 6. Remove the bolts shown in Fig. C. This will allow you to remove the air box. Fig. A Fig. B Fig. C i212-411 2004-2005 Kawasaki ZX10R – PCIII USB – 2 i212-411 www.powercommander.com Remove these bolts Remove screws Remove bolts 7. Locate the Throttle Position Sensor connector. This connector is located above the left hand side of the engine. This is a white 3 pin connector. Unplug this connector (Fig. D). 8. Plug the white connectors from the PCIII in-line of the stock TPS connector (Fig. E). 9. Locate the fuel rail connector behind the injector bodies (Fig. F). This connector is brown in color

Kawasaki Voyager 1700 Hitch Removal both saddlebags and Installation Instructions

0

Filed Under (Kawasaki) by admin on 08-05-2012

download
Remove the seat. Remove both saddlebags by removing the 3 bolts shown below Remove the plastic liner in the bottom of the trunk by gently pushing in on the center of the plastic clips Once the liner is removed remove the trunk rear light assembly by removing the 4 black screws in side the trunk and 4 on the bottom side of the light assembly. Unplug the light assembly and set it aside. Remove the bolts for the trunk Have a friend hold the trunk up and remove the 4 screws (two on each side) for the side trim Put the bolts back inside the trunk and tighten finger tight to make sure it does not fall. Remove the remaining side trim screws, 5 on each side, and remove the side trim and set it aside Remove 2 bolts from the saddle bag supports. Place the side plate mounting bracket behind the saddlebag supports and replace the two bolts you removed in the previous step. (We recommend using a few drops of Loctite). Do this step for both sides of the bike. Place the side plate behind the mounting bracket and attach the side plates to the mounting brackets with the two bolts supplied with the hitch (We recommend using Loctite on this step) Repeat this step for both sides of the bike

Kawasaki ZX-9R Ninja TiForce exhaust system Installation Instructions

0

Filed Under (Kawasaki) by admin on 07-05-2012

download
1. Remove the lower fairing. Remove thelower radiator mounting bolts, loosen the upper bolts and pivot the radiator forward to provide access to the exhaust nuts (flange nuts). Remove the oil cooler mounting bolts and pivot the oil cooler forward to provide access. 2. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 3. Inspect the exhaust gaskets. Replace if necessary. 4. Assemble the head pipes 1 (blue), 2 (red), 3 (yellow), and 4 (green) by matching the joints of the same color to the pair of front Y-pipes. Do not install the exhaust springs at this time. 5. 2000 through 2002 models ONLY!!! Place a billet aluminum exhaust port centering flange Z on each TiForce headpipe -see figure 3 for details. 6. Attachthe assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing for some adjustment in the remaining steps. Reuse the flange nuts saved from step 2 above. Make sure the ends of the headpipes fit flush and snug in the ports and centering flanges Z before tightening (’00-’02 ONLY). 7. Install the S-Bend to the front section of the headpipes and two Y-pipes. 8. Go back and retighten the head pipe flange nuts per factory specifications -make sure the headpipes and flanges Z are centered in each port (’00-’02 ONLY!!! ) . 9. Slide the TiForce end can into place. 10. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. See figure 1. 11. Place the bands approximately 108 mm from the edge of the end can. See figure 2. 12. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 13. Attach the supplied springs to all the joints, starting from the headpipes and working back to the end can. 14. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. 15. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (refer to step 11 /figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTIONWHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN.

Harley-Davidson Mid Kit POWERLET Installation Instructions

0

Filed Under (Harley Davidson) by admin on 07-05-2012

download
STEP #1 Remove seat. STEP #2 Route wires starting at the battery end and finishing at the bracket. STEP #3 Connect the wires to the socket. STEP #4 Mount the bracket on the horn bracket located under the gas tank. STEP #5 Fasten ty-wraps. STEP #6 Put everything you took off back on. Detailed Instruction: STEP #1 -Remove the seat exposing the battery. See the owner’s manual. STEP #2 – Remove negative battery lead. Remove the positive battery lead and attach the red wire [B]. Attach the black wire to the gas tank bolt [C]. Run the wires below the gas tank by passing through the gap between the frame & gas tank [D]. STEP #3 – Finish routing the wire under the tank and up to the horn bracket. Install the fuse in the fuse-holder. The center terminal is plus and the outer ring is negative (see dwg below). Apply either dielectric grease or Vaseline to the spade terminals. Connect the red wire to the positive spade terminal & the black wire to the negative terminal. Use a voltmeter to check if the polarity is correct. STEP #4 – On the left side of the bike, under the gas tank, locate the horn and bracket. Remove the acorn nut from the bracket [A]. You may need to remove the second nut also. Attach the Powerlet bracket utilizing the supplied chrome & rubber washers (if necessary). Adjust the bracket so it is aligned. Tighten to 8 Nm. STEP #5 – Apply the three ty-wraps. Use one to secure the fuse-holder and the other near point [D] and the third near the socket. Do NOT allow the harness to directly contact the motor or exhaust

KAWASAKI TERYX EFI Installation And Removal Instructions

0

Filed Under (Kawasaki) by admin on 06-05-2012

download
1. The Stage IV controller can be mounted in numerous places. Placement depends on personal preferences. Only mount in locations where no damage may occur from sharp or hot objects. 4. Start the UTV and in approximately four seconds the lights on the Stage IV controller will be visible. With a proper install, you should see lights going from side to side on the controller. This will last approximately eight seconds and then will stop. After lights have stopped going side to side, you will notice a great light on the left side of the controller. When you rev the motor, lights will increase across the controller and even change colors. 5. Double check all fasteners and connections. 7. The Stage IV controller has been programmed for ultimate performance when using Trinity Racing’s Stage IV exhaust system and Powerflow intake system on an otherwise stock engine. Different products, modifications, or other conditions may require additional adjustments. Please refer to Basic Tuning Adjustments and all final fuel adjustments are the customer’s responsibility. 8. You are now ready to ride! Enjoy your new Stage IV fuel management controller! Basic Tuning Adjustments 1. The following instructions are for basic fuel tuning. Modes 1,2, & 3 are allowing adjustments to increase and decrease the amount of fuel the engine needs. Modes 4 & 5 are for advanced tuning only. DO NOT change modes 4 & 5 when doing basic tuning! 2. To help understand how these modes work, you can think of them as if you were working with a carburetor. 3. Remember each time you push the MODE button you will be advancing to the next mode. Push the MODE button once and you are now in mode 1, push the MODE button again and you are now in mode 2 and so on. You only need to be concerned with modes 1, 2 & 3 for basic tuning. Modes 4 & 5 are for advanced tuning ONLY. 4. If you need to go back to the settings that were pre programmed when you purchased the controller, just look at the picture in each mode, the colored square represents where the settings were when you purchased the controller. 5. Looking at the controller you will see eight lights with numbers under them, this is what you need to look at when changing settings. The #1 light on the controller represents the leanest setting

Kawasaki Vulcan 500 Receiver Hitch Installation Manual

0

Filed Under (Kawasaki) by admin on 06-05-2012

download
1) Place motorcycle on its side stand on a firm level surface. 2) Remove saddlebags if any. 3) Remove rear riders pegs. 4) Attach front of bracket A (left side) and bracket B (right side) between rear footpeg motorcycle bracket and rear footpeg. Use new bolt provided (Bolt assortment included to accommodate some accessories) 5) Attach bracket E (left side) and bracket F (right side) to two rear fender attachment bolts. Use new bolts provided. (Bolt assortment included to accommodate some accessories) 6) Attach bracket C (left side) and bracket D (right side) to brackets E and F and to second holes on rear of hitch. 7) Attach rear of brackets A and B to BOTTOM of hitch arms 8) Tighten all bolts. Receiver hitch diagram Leveling stand screw jack installation After hitch is installed, install leveling stand screw jacks to hold motorcycle in an upright and level position in order to install or remove InstaTrike. 1) Thread right side screw jack into leveling stand bracket on bracket B and adjust leveling jack bolt out until motorcycle will be level against it. 2) Push motorcycle over from left side until right screw jack is touching floor.

KAWASAKI MULE Electric Steering Installation Manual And Removal

0

Filed Under (Kawasaki) by admin on 05-05-2012

download
Remove plastic center cap on steering wheel by prying off with a small screwdriver. Remove steering wheel nut and remove steering wheel by pulling up on wheel. If wheel is tight have a partner tap on the shaft while pulling up on wheel. Note: Do not mushroom threads on shaft. Remove all screws that retain dash to body of vehicle. Disconnect all electrical connections at back of dash. Mark all wires to ensure easy install. Remove lower steering shaft bolt at rack and pinion. Remove upper bolt at base of steering column. Remove the 2 bolts that retain the steering column to the frame and remove the column and the shaft assembly. Remove lower u-joint on steering column shaft & replace it with supplied u-joint. There is a welded wire retainer on the lower dash tube where the electric motor will sit. You will need to grind off this piece and smooth. Remove the master cylinder bolt closest to the driver side and discard bolt. Your motor and module has been shipped together bolted to the bracket. It is important to follow the install sequence to ensure a proper installation. The lower shaft on the steering motor is marked on the shaft and on the motor. These marks must not be changed. If you remove the shaft it needs to be installed back in the same spot.

2006 KTM 250 SX-F 250 EXC RACING 400 EXC RACING 450 SX, XC, EXC RACING 525 SX, XC, EXC RACING, REPAIR MANUAL

0

Filed Under (KTM) by admin on 05-05-2012

download
Hot start lever (250 SX-F) If you pull the red hot start lever [1] during the starting procedure backward, a bore in the carburetor will be opened through which the engine may take in additional air. The result is a „lean” fuel-air mixture of the type needed for hot starts.
ENGLISH 7 OPERATION INSTRUMENTS » Headlamp switch (EXCUSA) In this model the headlamp is switched on with the pull switch [1] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Starter button (EXC) Pushing the black starter button [2] will actuate the E-starter. Emergency OFF switch (EXC Australia) The red emergency-OFF switch [3] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [4] will actuate the E-starter. 2 3 4 5 6 Indicator lamps The green control lamp [5] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [6] lights up when the high beam is on