road king bag removal kit

You search Auto repair manual PDF road king bag removal kit, if there are search results will appear below. If search results do not exist, please search by others keyword.



  road king bag removal kit Direct Download speed 5282 Kb/s

  road king bag removal kit Full Version speed 6162 Kb/s



HARLEY DAVIDSON ROAD KING SOLO BUCKET AND PASSENGER PILLION INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
Installation SOLO SADDLE ONLY 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider solo seat. 2000 and later models . Remove the retainer washer from the stud plate and replace with two black retainer washers (2). Be careful not to allow stud plate to fall through the fender. 3. Road King standard models . Install stock solo seat mount bracket using two stock screws saved in Step 2. Road King Classic Custom models . Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. Install seat by sliding front of seat into seat holder bracket. Pull up on the nose of the seat to verify that the seat is securely installed. After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) 5. 1999 and later models . Install 1/4 in. star washers (6), spacers (4) and acorn nuts (3) onto rear mount studs. Torque to 72 in-lbs (8.13 Nm). 1998 and earlier models . Install 5/16 in. star washers (5) and 5/16-18 x 3/4 in. buttonhead screws (1) into stock mount nuts. Torque to 17 ft-lbs (23 Nm). SOLOAND PILLION 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. Retain all hardware for later use. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider seat. 3. Road King standard models. Install stock seat mount bracket onto new solo seat using two screws saved in Step 2. Road King Classic Custom models. Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. 1999 and later Road King standard models . Secure the rear mount bracket with stock mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). 1998 and earlier Road King standard models . Install solo seat by sliding front of seat into holder bracket on bike. Secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm). Road King Classic Custom models . Mount Kit Number 52903-01 is required for installation. Install solo seat (7) by sliding front of seat into holder bracket on bike. • 1999 and later models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). • 1998 and earlier models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm)

Incoming search terms:

Harley Davidson Road Rod Saddle Bag System Kit INSTALLATION Instructions

0

Filed Under (Harley Davidson) by admin on 16-04-2012

download
Use locktite on all fasteners!! 2. Put bike on lift and place jack under frame. Raise bike to lift rear wheel. 3. If swing arm pivot shaft is drilled and tapped on each end, they need to be redrilled and tapped to 3/8-16 to a depth of _” deep. If you are unable to drill & tap your swing arm pivot shaft, you can purchase one from Cycle Visions (part #CV6121), See Harley Davidson® V-Rod® Service Manual Section 2, Page 2.89 for removal and installation instructions. 4. Remove seat, passenger seat, turn signal module, rear fender cover, turn signal license plate assembly, and rear foot peg assemblies. NOTE: Our bag system will not work with stock exhaust system… we recommend the 2-into-1 Supertrap, or you may use any exhaust system that is lower than the rear axle bolt. 5. Remove the two upper shock bolts. Relocate the shock spacer from the right side to the left side, and use the new spacer supplied on the right side. 6. Install front bag mount between frame and spacer (see Figure 1), reinstall shock bolts and torque to 31-50 lbs. 7. Install lower bag support frame to swing arm pivot shaft using the 3/8″ bolt through rear foot peg clevis and cover (see in Figure 2). NOTE: There is a right and left covers and bag support, install accordingly. Torque to 35 foot lbs. 8. Install rear fender front mounting tabs using 8mm 1.25 x _ and flat washers (supplied in kit) (see Figure 3). 9. Install upright saddlebag support brackets to the lower bag mount assembly and lower fender extension crossover mount. (see Figure 4). Torque to 25 lbs. NOTE: Install crossover mount with gusset facing down. 10. Remove license plate light from your rear turn signal bracket license plate assembly. Install license plate light on our license plate light bracket (see Figure 5). 11. Install the license plate bracket on the inside of the rear fender extension using the top holes of the license plate frame (see Figure 6 & 7). 12. Install fender washers on the inside of the fender extension (see Figure 8). 13. Install upper fender bracket to rear fender extension with a _-20 bolt supplied in kit (see Figure 9). 14. Install rear fender extension with chrome button fitted bolts. (see Figure 10 & 11). 15. To check alignment and fit of rear fender extension reinstall original rear fender. Once you have everything lined up and fitted, remove original rear fender, drill & tap (2) two 5/16 x 18 holes in rear fender support bracket (see Figure 12). 16. Install Harley Davidson® Part #70909-95 and 47449-97 bracket and receptacle on front and rear bag supports (see Figure 13 & 14). 17. Install Harley Davidson® Part #47449-97 bracket with receptable (see Figure 14). Make sure the bolts come from the inside out. This bracket is adjustable for location.

HAR:EY DAVIDSON FLHR/C/S (Road King) FRONT END LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Removal (Left and Right Forks) 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to Touring Model Service Manual and remove front wheel, fender and brakes. 3. Refer to Touring Model Service Manual and remove headlamp nacelle. 4. Loosen fork cap bolt from fork tube plug at top of fork tube, but do not remove. 5. See Figure 1. Standing at front of vehicle, loosen pinch bolt (with lockwasher) on right side of lower fork bracket, but do not remove. 6. Spray glass cleaner on fork tube above the rubber fork stop. After lubricating surfaces, move fork stop up fork tube until it contacts bottom of upper fork bracket. 7. Holding fork slider to prevent fork from dropping, remove fork cap bolt from fork tube plug. Slide fork tube down and out of upper fork bracket, fork stop, lower fork bracket and slider cover. 1 WARNING 1 WARNING 1 WARNING 1 of 5 ® Kit Number 54614-05 Figure 1. Loosen Pinch Bolt on Lower Fork Bracket i04808 1 Fork cap bolt 2 Fork stop 3 Pinch bolt 8. Thread fork cap bolt back into fork tube plug to prevent loss of oil while handling. 9. Move forks to bench area. Place suitable drain pan on floor beneath vise. 10. Repeat Steps 2-6 to remove left fork. Left And Right Fork-Disassembly 1. Remove nuts, lockwashers, flat washers and axle holder from studs at end of fork slider. 2. See Figure 2. Obtain FORK TUBE HOLDER (Part Number HD-41177) and proceed as follows: a. Clamp end of tool in vise in a horizontal position with plastic knobs facing toward you. b. See Figure 3. With the fork cap bolt topside, clamp fork tube between rubber pads on inboard side of tool. Tighten knobs until fork tube is securely held. 3. Remove fork cap bolt from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug from fork tube. Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove 6mm screw from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and discard damper tube. 12. Remove wear ring and rebound spring. Discard rebound spring. Do not expand or stretch retaining clip to remove from fork tube or clip may become bent or distorted. 13. Using pick tool, remove retaining clip between fork slider and fork tube. 14. Remove fork tube from fork slider. NOTE To overcome any resistance, use the fork tube as a slide hammer, that is, first push fork tube into fork slider and then pull it outward with a moderate amount of force. Repeat this sequence until fork tube separates from fork slider. 15. Slide fork oil seal, slider spacer and slider bushing off end of fork tube. Discard fork oil seal and slider bushing. 16. Remove the lower stop. Right and Left Fork-Assembly Exercise caution to avoid scratching or nicking fork tube. Damaging tube can result in fork oil leaks after assembly. 1. See Service Parts Illustration. Obtain new Damper Tube (Item 7, Part Number 46532-04) from kit. Obtain new Rebound Spring (Item 8, Part Number 46273-02) from kit and install on opposite end. Install wear ring removed in step 12. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube. Install lower stop at end of damper tube. 3. Install fork slider in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (14) (Part Number 45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing down fork tube. 5. Slide slider spacer down fork tube until it contacts slider bushing.

Incoming search terms:

HARLEY DAVIDSON ROAD KING FAT HANDLEBAR KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
PREPARATION – ALL MODELS To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. See the service manual and remove the seat and disconnect battery cables or remove the main fuse. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will dama ge painted and bod y panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTES Immediately wipe up any brake fluid spills with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills). Cover nearby motorcycle surfaces with a polyethylene protective sheet to help protect against damage to finish caused by spilled D.O.T. 4 brake fluid. 2. See the service manual and drain the brake fluid from the front brake reservoir. ORIGINAL HANDLEBAR REMOVAL NOTE Cover the front fender and the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) 1. Using a T-40 TORX® drive head, remove and retain the button head screw on the underside of the fork stem and bracket assembly that holds the brake line manifold tee. 2. Carefully make note of the front brake line routing and the orientation of the banjo fittings. Disconnect the brake line from the front brake calipers and the front brake master cylinder assembly. Save the banjo bolts, but discard the two gaskets found at each banjo fitting. See FRONT BRAKE MASTER CYLINDER in the service manual. 3. Remove the old brake lines from the motorcycle. 4. Using a T27 TORX drive head, remove the front-brake master cylinder and clutch-lever assemblies (refer to CLUTCH CABLE in the service manual) from the stock handlebar.

HARLEY DAVIDSON SKULL FOOT BOARD INSERT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Kit 50704-04 is an Operator Footboard Insert Kit. •This kit fits all 2004 and later FLHRS/I (Road King® Custom) model motorcycles. •This kitalso fits 1986 and later FLHR/I/CI, FLHT/C/CI/CUI and FLTR/I models equipped with Swept-Wing footboard pans 50683-04 (right) and 50688-04 (left) . Kit 50704-04 contains the following items: QTY DESCRIPTION PART NO. 1Operator footboard insert (right) 50705-04 1Operator footboard insert (left) 50706-04 Kit 50707-04 is a Passenger Footboard Insert Kit. •This kitfits 2004 FLHTCSE models, and all 1986 and later Touring model motorcycles equipped with Swept- Wing Grooved Passenger Footboard Kit 50357-04 . Kit 50707-04 contains the following items: QTY DESCRIPTION PART NO. 1 Passenger footboard insert (right) 50708-04 1 Passenger footboard insert (left) 50709-04 Kit 50710-04 is an Operator Footboard Insert Kit. •This kitfits all 1980 and later Touring models except FLHRS, and 1986 and later FL Softail®model motorcy- cles equipped with footboard pans 50621-79A. Kit 50710-04 contains the following items: QTY DESCRIPTION PART NO. 1Operator footboard insert (right) 50711-04 1Operator footboard insert (left) 50712-04 Kit 50713-04 is a Passenger Footboard Insert Kit. •This kit fits all 1986 and later Touring models . •This kit also fits 1986 and later FL Softail models when equipped with accessory passenger footboard kits (Part Number 50602-89B, 50955-97A, 50955-00 or 50602-00). • This kit iscompatible with Chrome Passenger Footboard Cover Kits (Part Numbers 50782-91, 50193-96, 50194-96 and 50246-00). • This kit is notcompatible with Leather Passenger Footboard Fringe Kits (Part Numbers 50947-98 or 50956-98). Kit 50713-04 contains the following items: QTY DESCRIPTION PART NO. 1 Passenger footboard insert (right) 50714-04 1 Passenger footboard insert (left) 50715-04 Installation, Kit 50704-04 (For Swept-Wing Operator Footboards): Removing Previously Installed Inserts 1. Apply liquid dishwashing soap to the rubber beads protruding through the bottom of the footboard pan. 2. With the operator footboard in the “up” position, use a screwdriver to work the rubber footboard beads out through the top of the footboard. 3. Repeat the above steps for the remaining footboard insert. Installing the New Inserts 4. Apply liquid dishwashing soap to the rubber beads on the new footboard insert. 5. Place the footboard insert into position on the footboard pan. From the underside of the footboard, use a pliers to pull each rubber bead into its mating hole in the footboard pan until the beads protrude through the pan. 6. Repeat the above steps for the remaining footboard insert.

Incoming search terms:

Honda Motorcycle Na vigation Kit

0

Filed Under (Honda) by admin on 28-11-2010

download
Honda Motorcycle Na vigation Kit Honda Motorcycle Navigation Kit G e n e r i c A c c e s s o r i e s 2 0 0 8 For your peace of mind Honda Genuine Accessories are carefully designed, researched and stringently test ed tot he highest standards. And since they’re all Honda approved you’llknowthat they’rejustastoughand well made as your Honda motorcycle. Please Note -All prices quoted are correct at time of printing and are subject to change without prior notice. y e a r w a r r a n t y GENUINE ACCESSORIES Honda Motorcycle Navigation Kit Model Part Number Description RRP Remarks NAKED CBF 600 08A 40MER800B CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY CBF 600 08A 40MER800A CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY ON/OFF XL700V 08A 40MFF800 * CONTAINS NA VI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EARPH ONE, MANUAL, 08A 30MFF800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY XL 1000V 08A 40MBT800 CONTAINSNAVI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EAR PH ONE, MANUAL, 08A 30MBT800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY TOURERS/SPORT TOUR ERS DN-01 08A 40MEH800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, AND BATTERY -CONTAINS 08A 30MEW800 ADDITIONALSTE ERIN G HANDLE C LAMPS FORV ISU AL INTE GRAT ION OF THE COMPONENT NT700V 08A 40MEW800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, BATTERY

Incoming search terms:

Harley-Davidson Road King Classic Tour Pack INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
1. Close the bag completely. Support the outside of the bag with a covered piece of soft material to prevent marring or scratching. 2. Position the template on the outside of the bag, centered between the buckles. Align the template along the gap between the seams as shown at right. Tape the template in place. 3. Drill all of the small holes on the template using a 1/4″ drill bit for the assembly holes. Drill or punch the 3/4″ hole for the lock. 4. Sandwich the lock. item 4, between items 3 and 5 as shown above in FIG.1. Fasten it to the bag with the black slotted blind screws (items 7). Sandwich the leather between the lock cover plate (item 6) on the outside and the lock assembly. It may be necessary to remove a section of excess overlapped leather. 5. Use the phillips head screws (item 7) provided to attach the spring loaded ratched bar assembly. 6. Lock operation. *a. rotate the locking bar down as the bag is closed * * so that it is started into the lock aseembly. *b. check that the bag straps are outside of the bag. *c. Press the bag lid down as your help to align the * * bag lock assembly with the locking ratched bar. the ratchet bar whill operate smoothly into the * * lock when properly aligned.

HARLEY DAVIDSON CLUTCH CABLE ASSEMBLY INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
36753-87A This kit fits 1987 and later FXLR model motorcycles. 36755-87A This kit fits 1987 and later FXRS/SP model motorcycles. 38601-89 This kit fits 1988 and later FLTC, FLTC-Ultra, FLHS, FLHTC FLHTC-Ultra and FLHTP model motorcycles. 38606-87A This kit fits 1987 and later FXR, FXRS and FXRT model motorcycles. 38607-87A This kit fits 1987 and later FLST, FXST, FXSTC, FXRP, FLTC, FLHT, FLHTP and FLHTC model motorcycles. 38617-95 This kit fits 1995 and later FXSTSB model motorcycles. 38647-98 This kit fits 1998 and 1999 FXSTB model motorcycles. 38661-00 This kit fits2000 and later FXDL, FXDS-CONV and FXDWG model motorcycles. 38664-00 This kit fits2000 and later FXSTD model motorcycles. 38665-00 This kit fits2000 and later FXSTB model motorcycles. 38666-00 This kit fits2000 and later FXSTS, FLSTS, FLSTC, FLSTF, FXDX, FXD and FXST model motorcycles. 38667-00 This kit fits 2000 and later FLTR, FLTRI, FLHT, FLHTC, FLHTCI, FLHTCUI, FLHR, FLHRI, FLHRCI and FLHP model motorcycles. 38672-01 This kit fits 2001 and later FXDWG2 model motorcycles. Kit Contents: QTY DESCRIPTION 1 O-ring, rubber 1 Cable, clutch 1 Pin, cable pivot 1 Grommet (Kit no. 38607-87A, 38660-00A and 38667-00 only) Installation NOTE A Service Manual for your motorcycle is available from your Harley-Davidson dealer. A SERVICE MANUAL IS NEEDED TO INSTALL THIS KIT. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. 1. Refer to the Service Manual for your motorcycle model. Screw the cable adjuster all the way in to allow for maximum cable free play. 2. Remove clutch hand lever from hand-lever bracket at pivot pin. Remove original clutch cable from hand lever and transmission. Retain anchor pin bushings. 3. See Figure 1. Install lever end of new clutch cable. Position cable eyelet in clutch lever slot. Retain with new cable pivot pin through original bushings. NOTE See Figure 2. When routing cable on models where clutch cable passes through inner fairing (FLHTC, FLHTC-U and FLHTP with fairing), clutch cable eyelet may be too large to pass through clutch cable access hole in fairing. If this is the case, use the template supplied with this sheet to file out a hole to accommodate the new eyelet. Place the grommet included with kit no. 38607-87A, 38660-00A, and 38667-00 in the hole after filing. 4. Secure the clutch lever in the lever bracket with the lever pivot pin and retaining ring. 5. Follow steps outlined in the applicable Service Manual and install the transmission-end of the new cable with O- ring. 6. Adjust clutch cable according to procedure in Service Manual.

Incoming search terms:

HARLEY DAVIDSON HYBRID CAM PLATE AND HIGH FLOW OIL PUMP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Gasoline can drain from the carburetor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) NOTES Installing this kit requires removal and installation of the cam support plate. Refer to the service manual for instructions with the following exception pertaining to cam compartment compo- nents: The crank and primary cam sprocket flange bolts are specially hardened, and the flat washers are of a special diameter and have ground surfaces. Use ONLY the parts provided in the Drive Gear Retention Kit (H-D Part Number 25533-99A, sold separately) when installing this kit. -J04804 1 of 7
The cr ank sprocket flange bolts and pr imary cam sproc ket flange bolts ARE NOT interchangeable. 2. Refer to the service manual to remove and discard the crank sprocket flange bolts and primary cam sprocket flange bolts and washers. 3. For 1999 models only: Refer to the service manual to remove and discard the currently installed cam drive sprocket. 4. Refer to the service manual to remove and disassemble the cams from the support plate and oil pump. Discard the support plate and oil pump. 5. For 1999 – 2000 Dyna, 2000 Softail, 1999 – 2000 Touring, and 2001 EFI Touring models only: Inspect the cams, chain, sprockets and chain tensioners for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. For 2001 – 2005 Dyna, 2001 – 2006 Softail, 2002 – 2006 Touring, and 2001 carbureted Touring models only: Inspect the cams and secondary cam chain for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. The primary cam chain, primary sprockets and both tensioners will be replaced by new components from the kit. For ALL models and years: Discard the guide, as it will not be used. INSTALLATION 1. ALL models: See Figure 1. Obtain the new Rear Cam Roller Bearing Kit (H-D Part Number 8983) from inside the Cam Service Kit (H-D Part Number 17045-99C, purchased separately), and install as indicated in Step 2. NOTE See Figure 2. If not enough of the splined shaft is exposed to install the sprocket, omit the spacer (4) and proceed to Step 2e. When the bearing inner race is started onto the machined area, remove the flange bolt (5), flat washer (6) and sprocket, then assemble using the spacer (4). Repeat Step 2e to fully install bearing inner race. To center thrust washer, be sure o-ring is installed in relief groove. Damage to bearing cage and engine can occur if thrust washer is not centered. (00473b) 2. See Figure 1. Install the O-ring (5), thrust washer (4) and bearing inner race (3) onto the rear camshaft as follows: a. See Figure 2. To properly locate the thrust washer (2), install the O-ring (3) in the grinding relief groove on the splined end of the rear camshaft between the machined area and the secondary cam sprocket.

Incoming search terms:

HARLEY DAVIDSON HEEL REST KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
Models Kit 50227-01 is designed for forward controls and fits: •1989 and later FX Softail Models with Original Equipment (OE) Forward Controls, •1993 through 2002 FXDWG, •Dyna models equipped with Forward Control Kit 49080- 93 or 49080-93A. Kit 50227-01 does not fit Dyna models equipped with Forward Control Kit 49080-03 or Forward Control Footrest Support 33695-03 (left) or 33697-03 (right). Kit 50236-01 is designed for mid controls and fits: •all 1990 and later Dyna Model Motorcycles with Original Equipment (OE) Mid Controls. Additional Parts Required Proper installation of this kit also requires installing a pair of Heel Rest Pegs, or Shifter Pegs, which can also be mounted as heel rests. Refer to the appropriate Parts Catalog for stock shifter pegs, sold separately. The current Harley-Davidson Genuine Motor Accessories and Parts catalog also has a selection of Heel Rest Pegs or Shifter Pegs and matching Footpegs. Any shifter peg style that is symmetrical in design can be used as a left or right side heel rest. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE A Service Manual for your model motorcycle is available from a Harley-Davidson Dealer. Kit Contents See Figure 1 and Table 1. INSTALLATION NOTE See Figure 1 for the following procedure. 1. Remove the screw (B), lock nut (C) and spring washer (E) securing the left footpeg to the footrest support bracket (A). Save the hardware for later installation. NOTE Heel rest levers are side-specific. Levers mount so the set screws are on the underside. 2. Obtain a Heel Rest Peg or Shifter Peg (D) (purchased separately) and the left side heel rest lever (3). Apply Loctite® 243 (7) to the threads of the peg and install it to the left heel rest lever. 3. Obtain the screw (B), spring washer (E) and lock nut (C) removed in step 1, and the heel rest lever and peg assembly (D). Position the lever assembly to the desired angle on the mount, and slide the lever assembly with the spring washer into the footrest support bracket as shown. NOTE Splines on the lever and mount provide for a limited range of heel rest angle adjustment. For Kit 50227-01. The heel rest lever (3) can be adjusted after the mount (1) is attached but before the set screw (2) is installed. Slide the lever inward off the spline, and rotate it to the desired angle. For Kit 50236-01. The heel rest lever (3) angle cannot be adjusted after the mount (1) is attached without removing them from the footrest support bracket (A). Check to ensure the heel rest (D) is in a comfortable position before tightening the mounting hardware. 4. Install the original screw (B) and lock nut (C) to secure the heel rest assembly to the footpeg mount. Tighten to 33 ft- lbs (45.6 Nm). 5. Obtain a screw (6), spring washer (5) and nut (4) from the kit. Install the footpeg to the heel rest assembly and tighten to 33 ft-lbs (45.6 Nm). 6. Obtain a set screw (2) from the kit. Apply Loctite® 243 (7) to the threads, and install the set screw to the heel rest lever. Tighten to 16 in-lbs (1.8 Nm). 7. Perform Steps 1 through 6 for the right side. USE

Incoming search terms:

Incoming search terms: