vfr800 centre stand weight

You search Auto repair manual PDF vfr800 centre stand weight, if there are search results will appear below. If search results do not exist, please search by others keyword.



  vfr800 centre stand weight Direct Download speed 5282 Kb/s

  vfr800 centre stand weight Full Version speed 6162 Kb/s



Harley-Davidson The WHEELDOCK EZ-UP Center Stand Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2012

download
Unlike other center stands, the WHEELDOCK EZ UP stand requires very little effort to operate and can usually be done while still on the bike by simply pushing down on the foot lever with your left foot. Once you feel both feet of the center stand in contact with the ground, transfer your weight up off of the seat and onto the foot lever of the center stand. The stand should rotate under the bike and a bit forward lifting the bike quite easily. CAUTION: Never attempt to raise the bike with a passenger on board, as you will damage the foot lever. You can also raise the bike on the center stand by using the following traditional method: Place the bike on the side stand and step off to the side. From the left side of the bike, push the bike up to the vertical position and press down on the foot lever until both feet of the stand are in contact with the ground. Now apply weight to the foot lever while lifting up on the bike. For cleaning the rear wheel: first place a ½-inch piece of plywood under the stand and use this (beside the bike) method for placing the bike up on the plywood spacer; this will allow the wheel to rotate freely for cleaning. Do not try this while on the bike, as it will require too much foot pressure on the lever. You now have two options to get the bike off of the stand: You can simply rock the bike forward, or put the bike in gear and drive off in most cases as long as you are parked on a flat, level surface. Tips for solving common questions: If you have the correct height stand and you still have difficulty getting the bike up on the stand check the following: the bike must be in neutral, the wheel should be straight forward and not cocked, do not hold the front brake lever and make sure you have 15 lb or more air pressure in the rear suspension. These are the most common problems we encounter

Incoming search terms:

Harley-Davidson touring bikes WHEELDOCK EZ-UP Center Stand Installation Instructions

0

Filed Under (Harley Davidson) by admin on 18-04-2012

download
Unlike other center stands, the WHEELDOCK EZ UP stand requires very little effort to operate and can usually be done while still on the bike by simply pushing down on the foot lever with your left foot. Once you feel both feet of the center stand in contact with the ground, transfer your weight up off of the seat and onto the foot lever of the center stand. The stand should rotate under the bike and a bit forward lifting the bike quite easily. CAUTION: Never attempt to raise the bike with a passenger on board, as you will damage the foot lever. You can also raise the bike on the center stand by using the following traditional method: Place the bike on the side stand and step off to the side. From the left side of the bike, push the bike up to the vertical position and press down on the foot lever until both feet of the stand are in contact with the ground. Now apply weight to the foot lever while lifting up on the bike. For cleaning the rear wheel: first place a ½-inch piece of plywood under the stand and use this (beside the bike) method for placing the bike up on the plywood spacer; this will allow the wheel to rotate freely for cleaning. Do not try this while on the bike, as it will require too much foot pressure on the lever. You now have two options to get the bike off of the stand: You can simply rock the bike forward, or put the bike in gear and drive off in most cases as long as you are parked on a flat, level surface. Tips for solving common problems: If you have the correct height stand and you still have difficulty getting the bike up on the stand check the following: the bike must be in neutral, the wheel should be straight forward and not cocked, do not hold the front brake lever and make sure you have 15 lb or more air pressure in the rear suspension. These are the most common problems we encounter.

Incoming search terms:

HARLEY DAVIDSON CHROME DISPLAY STAND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and disconnect the battery negative (-) cable or remove the main fuse. NOTE Make sure that the cutout (B) of the strap (3) is oriented to the rear of the motorcycle after installation. 2. See Figure 2. Install strap (3) and weld nut (4) to the frame in the locations shown. 3. Position the center display stand over the mounting holes under the frame, oriented so that the skid plate faces for- ward. 4. Apply a small amount of Loctite 271 – Red to the two long screws (1) and secure the rear of the display stand to the frame by installing the two screw to the strap. 5. Apply a small amount of Loctite 271 – Red to the short screw (2) and secure the front of the display stand to the frame by installing the screw to the weld nut. 6. Tighten screws to 60-96 in-lbs (7-11 Nm) . 7. Refer to the service manual and connect the battery cables or install the main fuse. 1 2 is05370 1. Flange side 2. Flat side Figure 1. Chrome Display Stand Foot Orientation ADJUSTING THE DISPLAY STAND The left and right feet of the display stand are independently adjustable to vertically level the vehicle with the display stand extended. To adjust the display stand: NOTE The display stand can be adjusted with rear tire to ground contact or with rear tire off the ground. With the rear tire to ground contact adjustment, the rear wheel is on the ground but enough weight is on the display stand legs to make the motorcycle stable from side-to-side and front-to-back. Using the display stand to center the motorcycle will require effort. With the rear tire off the ground adjustment, the rear tire clears the ground so tire can be rotated for cleaning or maintenance purposes. Using the display stand to lift rear tire off the ground will require more effort. Do not center the vehicle with someone on the vehicle. To reduce effort, remove stored items from saddlebags, if equipped

Incoming search terms:

Turbo+2 , Roadstar , Quantum Sport , Quantum"GL" , Entourage Owners Manual

0

Filed Under (Uncategorized) by admin on 03-12-2010

download
tracking Any parting within the tread, sidewall, or inner liner of the tire extending to cord material. CT A pneumatic tire with an inverted flange tire and rim system in which the rim is designed with rim flanges pointed radially inward and the tire is designed to fit on the underside of the rim in a manner that encloses the rim flanges inside the air cavity of the tire. Curb weight The weight of a motor vehicle with standard equipment including the maximum capacity of fuel, oil, and coolant, and, if so equipped, air conditioning and additional weight optional engine. Extra load tire A tire designed to operate at higher loads and at higher inflation pressures than the corresponding standard tire. Groove The space between two adjacent tread ribs. Gross AxleWeight Rating The maximum weight that any axle can support, as published on the Certification /VIN label on the front left side of the trailer. Actual weight determined by weighing each axle on a public scale, with the trailer attached to the towing vehicle. Gross Vehicle Weight Rating The maximum weight of the fully loaded trailer, as published on the Certification /VIN label. Actual weight determined by weighing trailer on a public scale, without being attached to the towing vehicle. Hitch Weight The downward force exerted on the hitch ball by the trailer coupler. Innerliner The layer(s) forming the inside surface of a tubeless tire that contains the inflating medium within the tire. Innerliner separation The parting of the innerliner from cord material in the carcass. Intended outboard sidewall The sidewall that contains a white-wall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire or the outward facing sidewall of an asymmetrical tire that has a particular side that must always face outward when mounted on a vehicle. Light truck (LT) tire A tire designated by its manufacturer as primarily intended for use on lightweight trucks or multipurpose passenger vehicles. Load rating The maximum load that a tire is rated to carry fora given inflation pressure. Maximum load rating The load rating fora tire at the maximum permissible inflation pressure for that tire. Maximum permissible inflation pressure he maximum cold inflation pressure to which a tire maybe inflated.
-9- Maximum loaded vehicle weight The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Measuring rim The rim on which a tire is fitted for physical dimension requirements. Pin Weight The downward force applied to the 5thwheelor gooseneck ball, by the trailer kingpin or gooseneck coupler.

Incoming search terms:

HONDA 1100 ACE, AERO AND SABRE CENTERSTAND INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 27-12-2010

download
Relocation of Regulator. Laying under the right side of the motorcycle, locate the voltage regulator. (finned aluminum box-approximately 3″x 4″) Note: See photo #1 – regulator already relocated. Remove the (2) 10 mm bolts attaching the regulator to the frame. Attach the bracket supplied to the regulator as shown. Using the original bolts, attach the regulator and bracket assembly to the frame as shown in photo #1 using the two 10 mm bolts supplied. Clamping Centerstand to Frame . Notice the centerstand is shipped with (2) white plastic washers. Note: See photo #2-A These are in place to overcome the spring tension or lock the stand in place and allow you to pivot the lower stand down partially to make installation easier. Pivot the upper stand about half way from the retracted to the extended (down) position. Note: This will require some force. If the stand will not stay in the position you can further tighten the two 9/16″ pivot nuts. Remove the bolts from the four band clamps. Wrap the (2) small clamps around the small upper frame tube and start the bolts so that the bolt will be at the bottom of the tube and the wrench head facing towards the rear of the motorcycle. Note: See photo #2. Center the stand on the frame from side to side so as to gain even clearance between the feet on the centerstand and the rear tire when the stand is in the retracted position. Holding the larger cradle up against the frame, tighten the (2) small clamps enough to hold the centerstand in place. Install one of the large clamps as shown in photo #3-A. Install the 2nd large clamp as shown in photo #2-C. Again retract the stand and check that the feet have even amounts of space from the side of the rear tire. Tighten the flour clamps securely 5-7 ft. lbs. Next remove the (2) 9/16″ pivot nuts and the white plastic washers as shown in photo #2-A. Re-install and tighten the 9/16″ pivot nuts securely 8-12 ft lbs. With the stand in the retracted position-adjust the stop bolt and lock nut, see photo #3-B, so that the stand is parallel with the ground and does not come in contact with any parts of the motorcycle. Using your new centerstand . To put the motorcycle up onto the centerstand, hold the left handle bar and saddlebag guard rail or grab under the bottom of the seat. Using the ball of your right foot, lower the stand to the ground. Rock the motorcycle from side to side slightly until you feel both feet of the stand touching the ground. Now put all of your weight onto the centerstand pedal (stand on it). Pull up and back on the grab rail or seat using a rocking motion to rock the motorcycle up onto the stand. Remember it is a matter of using your body weight and leverage not lifting!

Motorcycle stand Wheel chock set up and operating instructions

0

Filed Under (Tips and Review) by admin on 22-11-2010

download
1. can be adjusted to fit the wheel length. The Motorcycle Stand will fit most standard motorcycles currently on the market. However, some models with especially wide tires or custom low-profile front fenders will not fit. Mount the Support Arm (4) to the front of the Base using 2 Bolts (12), Washers 2. (5), and Nuts (6). Insert Pin (9) through the mounting holes and Cradle Stop (3); secure with Wash- 3. er (10) and R Pin (11). Insert Pin (9) through the mounting holes and Wheel Adapter (2); secure with 4. Washer (10) and R Pin (11). Securely tighten all hardware before use. 5. the Motorcycle stand must be mounted securely before use. 6. Page 5 SKU 97841 For technical questions, please call 1-800-444-3353. Mounting in concrete Choose a location to install the Motorcycle Stand that is flat, level, and capable of 1. bearing the combined weight of the Motorcycle Stand and the motorcycle being secured. The location should not obstruct walkways and provide enough room to retrieve the motorcycle after it is mounted. The surface of the location should be one suitable for the mounting of heavy equipment. Use the mounting holes in the Base (1) of the Stand as a template. Arrange the 2. Base in the chosen location and mark where the holes are to be drilled. You will need concrete anchors (not included) to secure the Base to the concrete 3. floor. Using the correct size concrete drill bit (not included), drill the mounting holes to secure the Base. Attach the concrete anchors to the floor. Secure the Base to the floor using con- 4. crete anchors.

YAMAHA ROYAL STAR VENTURE CENTERSTAND REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 31-12-2011

download
Stand Installation. Locate the four mounting holes on the frame that correspond with the holes in the centerstand. Slide the front of the centerstand up into the frame and align the large bolt holes with those in the frame. Install the (2) 7/16″ x 1″ bolts with washers thru the frame and centerstand. Install the (2) 7/16″ nuts and make finger tight. (on California models the fuel tank vent canister must be removed and the hoses bypassed see note below) Pivot the rear of the centerstand up to align the (2) smaller holes in the stand with those in the frame. Insert a phillips screwdriver into one of the (2) remaining mounting holes and pry the other hole into alignment. Install one of the ¼” x ¾” bolt with a washer from the top down thru the frame and centerstand. Install the lock nut finger tight. Remove the screwdriver and install the remaining ¼”x¾” bolt washer and nut. Tighten the ¼ ” bolts securely 10-12 ft. lbs., then tighten the 7/16″ bolts securely 20-24 ft. lbs. 2. Stop Bumper Installation. Next install the centerstand-stop bumper and bracket onto the frame. Locate the bolt “A” in photo #1. Notice there is another 10 mm bolt just below it. Remove the lower bolt. Attach the bumper bracket to this hole using the longer bolt and washer supplied. The leg of the bracket with the bumper should face inward towards the center of the motorcycle. Adjust the height of the bracket to keep the pedal arm 3/8″ to ½” from the bottom of the exhaust pipe. Tighten securely. 3. Emissions Valve Relocation. You will notice that the right leg of the stand near the foot comes in contact with the emissions valve. The valve needs to be moved outward or to the right as you are sitting on the motorcycle approximately ¾”. This is done as follows: Remove the (2) 10 mm bolts holding the emission valve and bracket to the frame. See photo #2. With the hoses still attached pull the valve down to gain access to the (3) allen screws. Remove the (3) allen screws and (2) nuts holding the bracket to the valve, turn the bracket over and re-assemble the valve onto the bracket as shown in photo #3. Re-install the valve onto the frame. You may need to rotate the hose clamp clips out of the way and/or bend the entire valve bracket assembly outward slightly to gain clearance between the centerstand leg and foot. 4. Using Your New Centerstand. To put the motorcycle up onto the centerstand, hold the left handle bar and saddlebag guard rail. Using the ball of your right foot, lower the stand to the ground. Rock the motorcycle from side to side slightly until you feel both feet of the stand touching the ground. Now, put all of your weight on to the centerstand pedal (stand on it). Pull up and back on the grab rail using a rocking motion to rock the motorcycle up on to the stand. Remember it is a matter of using your body weight and leverage not lifting! 5. Getting the Bike Down off the Centerstand. Holding the left handle bar and saddlebag guardrail, firmly rock the motorcycle off the centerstand. You can also rock it off while sitting on the motorcycle.

HARLEY DAVIDSON FL SOFTAIL FOWARD CONTROL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 31-03-2011

download
INSTALLATION Shifter Side, Left Block or jack vehicle under frame in a way that the vehicle will not fall over. Failure to properly block and/or raise the vehicle could result in death or serious injury. (00462c) 1. Block the motorcycle under the frame so that it is upright and level, with the weight off of the jiffy stand. 2. Remove footpeg. 3. Remove jiffy stand, shifter linkage and bracket per applicable Service Manual instructions, retaining hardware. 4. See Figure 5. Obtain the new left side shifter bracket (2), and three TORX® screws (3) from the kit. 5. Place washers previously removed on the screws. Apply LOCTITE® 243 (Blue) to the threads, and install the new bracket assembly to the motorcycle frame. Tighten the screws to 40 ft-lbs (54.2 Nm) . 6. See Figure 5. Install footpeg with spring washer (8), clevis pin (10) and retaining ring (9). If leg stop is incorrectly installed, excessive wear can allow vehicle to fall when rested on jiffy stand, which could result in death or serious injury. (00479b) 7. Install jiffy stand and attach the spring. When properly installed, the hook on the spring side connected to the bracket will face upward. 8. Verify that rubber bumper is in place on prong of jiffy stand. Without the bumper, the stand will make hard contact with the primary drive cover when retracted, which may result in damage to the cover. 9. Extend and retract the jiffy stand leg several times to verify proper operation. The stand should swing freely to the fully extended and fully retracted positions. 10. Refer to applicable Service Manual and re-attach the shifter linkage

1300 Yamaha V-Star Installation Manual

0

Filed Under (Yamaha) by admin on 07-11-2010

download
1) Place motorcycle on a firm level surface and secure in a upright position. 2) Remove saddle bags and saddle bag hardware (Tourer model only) Also remove rear riders pegs (Tourer model requires removal of rear footpeg offset hardware as well) 3) Attach bracket A (right) / B (left) to rear footpeg attachment point using new bolts provided. Remount footpegs/saddlebag hardware over top of brackets A/B. NOTE: Do not attach leveling stand bracket at this time 4) Attach bracket C(right) / D(left) to rear fender sub frame using new bolts provided. (Tourer model only – Saddle bag hardware mounts to the outside of brackets C/D. Brackets C/D mount between chrome side rail and saddlebag hardware.) NOTE: Brackets C/D have welded spacers which attach in toward rear fender 5) Attach top of Bracket E(right) / F(left) to rear of brackets C/D. Brackets E/F mount to the inside of brackets C/D. NOTE: Use ½ inch spacer between brackets E/F and C/D on Tourer model ONLY
6) Attach rear of brackets A/B to TOP of forward hitch arms. Attach bottom to brackets E/F to rear hitch plate. 7) Carefully tighten all bolts at this time ensuring hitch is square with motorcycle. Hitch Bracket Identification Leveling stand screw jack installation 1) Attach leveling stand brackets to brackets A and B 2) Thread right side screw jack into threaded hole on leveling stand bracket attached to bracket A sand adjust leveling jack bolt out. 3) Push motorcycle over from left side until right screw jack is touching floor. 4) Thread left side screw jack into threaded hole on leveling stand bracket attached to bracket B and adjust out until motorcycle will rest upright on both screw jacks. 5) Adjust screw jacks until motorcycle is level. 6) After InstaTrike is attached to or removed from receiver hitch, be sure to remove leveling stands and leveling stand brackets. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position.
INSTALLATION OF THE TOW-PAC HITCH CART. 1. Place your motorcycle on a smooth flat surface, like a garage floor, and install leveling stands. Install right leveling stand first. Carefully raise motorcycle off of side stand and install left leveling stand. Caution – Use leveling stands to level motorcycle ONLY. Do not raise motorcycle with stands Caution – Be certain that motorcycle is always in a stable balanced position when installing leveling stands. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt

Incoming search terms:

2008 CBR1000RR replace the clutch inner

0

Filed Under (Honda) by admin on 06-11-2011

download
Clamping Centerstand to Frame. Notice the centerstand is shipped with (2) white plastic washers. Note: See photo #2-A These are in place to overcome the spring tension or lock the stand in place and allow you to pivot the lower stand down partially to make installation easier. Pivot the upper stand about half way from the retracted to the extended (down) position. Note: This will require some force. If the stand will not stay in the position you can further tighten the two 9/16” pivot nuts. Remove the bolts from the four band clamps. Wrap the (2) small clamps around the small upper frame tube and start the bolts so that the bolt will be at the bottom of the tube and the wrench head facing towards the rear of the motorcycle. Note: See photo #2. Center the stand on the frame from side to side so as to gain even clearance between the feet on the centerstand and the rear tire when the stand is in the retracted position. Holding the larger cradle up against the frame, tighten the (2) small clamps enough to hold the centerstand in place. Install one of the large clamps as shown in photo #3-A. Install the 2 nd large clamp as shown in photo #2-C. Again retract the stand and check that the feet have even amounts of space from the side of the rear tire. Tighten the flour clamps securely 5-7 ft. lbs. Next remove the (2) 9/16” pivot nuts and the white plastic washers as shown in photo #2-A. Re-install and tighten the 9/16” pivot nuts securely 8-12 ft lbs. With the stand in the retracted position-adjust the stop bolt and lock nut, see photo #3-B, so that the stand is parallel with the ground and does not come incontact with any parts of the motorcycle

Incoming search terms: