HARLEY DAVIDSON HEEL REST KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
Models Kit 50227-01 is designed for forward controls and fits: •1989 and later FX Softail Models with Original Equipment (OE) Forward Controls, •1993 through 2002 FXDWG, •Dyna models equipped with Forward Control Kit 49080- 93 or 49080-93A. Kit 50227-01 does not fit Dyna models equipped with Forward Control Kit 49080-03 or Forward Control Footrest Support 33695-03 (left) or 33697-03 (right). Kit 50236-01 is designed for mid controls and fits: •all 1990 and later Dyna Model Motorcycles with Original Equipment (OE) Mid Controls. Additional Parts Required Proper installation of this kit also requires installing a pair of Heel Rest Pegs, or Shifter Pegs, which can also be mounted as heel rests. Refer to the appropriate Parts Catalog for stock shifter pegs, sold separately. The current Harley-Davidson Genuine Motor Accessories and Parts catalog also has a selection of Heel Rest Pegs or Shifter Pegs and matching Footpegs. Any shifter peg style that is symmetrical in design can be used as a left or right side heel rest. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE A Service Manual for your model motorcycle is available from a Harley-Davidson Dealer. Kit Contents See Figure 1 and Table 1. INSTALLATION NOTE See Figure 1 for the following procedure. 1. Remove the screw (B), lock nut (C) and spring washer (E) securing the left footpeg to the footrest support bracket (A). Save the hardware for later installation. NOTE Heel rest levers are side-specific. Levers mount so the set screws are on the underside. 2. Obtain a Heel Rest Peg or Shifter Peg (D) (purchased separately) and the left side heel rest lever (3). Apply Loctite® 243 (7) to the threads of the peg and install it to the left heel rest lever. 3. Obtain the screw (B), spring washer (E) and lock nut (C) removed in step 1, and the heel rest lever and peg assembly (D). Position the lever assembly to the desired angle on the mount, and slide the lever assembly with the spring washer into the footrest support bracket as shown. NOTE Splines on the lever and mount provide for a limited range of heel rest angle adjustment. For Kit 50227-01. The heel rest lever (3) can be adjusted after the mount (1) is attached but before the set screw (2) is installed. Slide the lever inward off the spline, and rotate it to the desired angle. For Kit 50236-01. The heel rest lever (3) angle cannot be adjusted after the mount (1) is attached without removing them from the footrest support bracket (A). Check to ensure the heel rest (D) is in a comfortable position before tightening the mounting hardware. 4. Install the original screw (B) and lock nut (C) to secure the heel rest assembly to the footpeg mount. Tighten to 33 ft- lbs (45.6 Nm). 5. Obtain a screw (6), spring washer (5) and nut (4) from the kit. Install the footpeg to the heel rest assembly and tighten to 33 ft-lbs (45.6 Nm). 6. Obtain a set screw (2) from the kit. Apply Loctite® 243 (7) to the threads, and install the set screw to the heel rest lever. Tighten to 16 in-lbs (1.8 Nm). 7. Perform Steps 1 through 6 for the right side. USE

Incoming search terms:

HARLEY DAVIDSON TOURING LAYBACK LICENSE PLATE MOUNTING KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-02-2011

download
This kit fits all 1999 and later FLHR (Road King®) models, FLTR (Road Glide®) and FLHT (Electra Glide® standard) models having license plates measuring a maximum of 7-1/4 x 4-1/4 inches (184 x 108 mm). Also fits 2003 FLHRSEI2 (Screamin’ Eagle® Road King). Does not fit with Detachable Tour-Pak Rack, part number 53276-04. Does not fit 2002 FLHRSEI (Screamin’ Eagle Road King). Kit Contents See Figure 1. INSTALLATION 1. Remove the license plate from the vehicle (if installed). Remove the two hex head bolts holding the original equipment (O.E.) license-plate bracket in place. The bolts and license-plate bracket can be discarded. 2. See Figure 1. Install the new layback license plate holder (1) using the button-head hex socket screws (3) from the kit. Tighten the screws to 19 ft-lbs (25.8 Nm) . 4 1 3 7 5 2 6 is02737 1. License plate holder, layback 2. Foam pad (6) 3. Screw, button head, hex socket (2) 4. License plate frame 5. Set screw, socket head (2) 6. Hex key 7. Reflector assembly, Part Number 59365-07 Figure 1. Layback License Plate Mount Components 3. Position the license plate onto the foam pads (2) of the license plate holder, centering and aligning the plate parallel to the holder edges for best appearance. NOTE Slots in the inside top edge of the license plate frame (4) fit over the two tabs on the top edge of the license plate holder. 4. Hook the top of the license plate frame over the top edge of the holder. Swing the bottom edge of the frame inward, holding the license plate in position against the pads. 5. Use the hex key (6) from the kit to securely fasten the license plate frame to the holder with the two socket head set screws (5)

HARLEY DAVIDSON REAR AXLE-NUT COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
REAR AXLE-NUT COVER KIT GENERAL Kit Number 41704-09, 41705-09, 41706-09 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section (English only). Additional Parts Required The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 1 and Table 1. INSTALLATION NOTES The shorter axle-nut cover mounts to the right side of the motorcycle. Axles that have been removed for service, replacement or repair may have been assembled in reverse orientation from their stock design. Axle-nut covers may not fit properly on reversed axles. Refer to the appropriate Service Manual for correct axle orientation. 1. Adjust the position of the exhaust system (if necessary) to provide axle-nut clearance. 2. Position each axle-nut cover over the appropriate axle nut. 3. The skull version nut covers have two set screws per cover. Position the logo and snug up one set screw to hold in place and the other to prevent rotation. 4. Tighten the axle-nut cover set screws to 70 in-lb (7.9 Nm) . NOTE The set screws in this kit are treated with a thread-locking compound. When replacing or re-installing the set screws (2), apply Loctite® 243 (Blue) Threadlocker and Sealant (Harley- Davidson Part Number 99642-97) to the set screw threads. SERVICE PARTS

Incoming search terms:

DRIVER PEGS HONDA ADAPTOR INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Assemble the peg onto the peg adaptor by removing the allen bolt from the end of the foot peg you are using. Remove the clevis assembly (folding mechanism) from the peg itself. Assemble the peg and allen bolt on to the peg adaptors. 2. The original peg pivots or folds up on a pin and has a return spring. Note how the spring is assembled into the peg. Remove the cotter pin, washer and pivot pin and foot peg. Install the new peg and adaptor assembly onto the motorcycle in the same manner and using the same spring, pin, washer and cotter pin. Set the angle of the new peg as desired and tighten the allen bolt securely. 3. Use the small set screws located at the end of the adaptors to raise and lower the foot pegs resting position.

1996-2003 KAWASAKI ZX7R INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) It is mandatory to use blue Loc-tite on all bolts. We promise they will come loose if you don’t. 2) Remove the large nut and washer that holds your triple clamp on. Install the new nut that we provide which has HEX drive facing UP. You will NOT use the stock washer. 3) Torque the new nut to your factory recommended setting as they vary. Normally a minimum of 50-80 ft lbs. 4) Install the new triple clamp damper mount (TC mount) over the new triple clamp nut with the “machined register” (the small knub) indexing into the matching groove on the top, back of your stock triple clamp. The knub insures the mount cannot spin should the damper try to loosen the main nut. 5) Be sure this TC mount is setting down flush on the triple clamp surface all the way around. This part is machined precisely to fit over the Scotts triple clamp nut. The groove machined into the nut is positioned so once the set screws are tightened, it will suck the TC mount down against your triple clamp. Remove any obstructions that would not allow the TC mount to sit flush against your stock triple clamp surface. 6) Tip to save time: Before installation, using Loc-tite start all the setscrews first, until flush with the inside bore. 7) Using blue loc-tite on the setscrews, run them all in against the nut equally and then proceed to tighten each one making your way around until they are all equally tight. They should be checked after the first ride as normally they will settle into the groove in the nut and require tightening. 8) (Note: You must use some heat to compromise the Loc-tite before trying to remove the setscrews or the small Allen head setscrews can be stripped easily). 9) Remove the two, stock-front tank retaining bolts. You will replace these with longer ones in the kit. 10) Install the new “frame bracket tower”. There is a front and back to this part, note the picture! 11) Install the longer tank bolts supplied, through our frame bracket and into your tank mounting holes. 12) Grease the tower pin and drop it in the tower pin hole. It is designed to “float” and requires no retaining devices. Keep the tower pin and hole portion greased lightly. 13) Install the damper using the (2) 6×20 Allens. The link arm slot aligns with the flats on the tower pin. 14) Read your damper manual for initial settings on the controls. The damper is infinitely adjustable and totally up to the user to find their preference. Start with softer (counter clockwise) settings. Normally where we set the unit is a good starting point, usually 8 clicks out on the base valve. 15) The base valve controls the immediate feel of damping forces exerted

Incoming search terms: